Preparing for Your Hadlima PushTouch Injection
Before you begin the injection process, careful preparation is essential to ensure a smooth and safe procedure. Gather all necessary supplies and follow these steps:
Gather Supplies
- One Hadlima PushTouch autoinjector: Confirm it is the correct dose prescribed by your doctor and has not expired.
- One alcohol swab: For cleaning the injection site.
- One cotton ball or piece of gauze: For applying gentle pressure after the injection.
- A sharps disposal container: A puncture-resistant, hard plastic container for safely discarding your used autoinjector.
Pre-Injection Preparation
- Wash Your Hands: Thoroughly wash your hands with soap and water and dry them completely.
- Inspect the Autoinjector: Take the autoinjector out of the refrigerator and let it sit at room temperature for 15 to 30 minutes before use. This makes the injection more comfortable. Inspect the liquid in the viewing window to ensure it is clear and colorless to pale brown. Do not use the autoinjector if the liquid is cloudy, discolored, or contains particles.
- Choose and Clean the Injection Site: Select an injection site from the recommended areas: the front of your thigh or your lower abdomen, at least 2 inches away from your belly button. Always rotate your injection site to avoid soreness. Use an alcohol swab to clean the skin in a circular motion and allow it to dry completely before injecting.
Administering the PushTouch Injection
The Hadlima PushTouch autoinjector has a buttonless design, meaning the injection is activated by pressing the device firmly against the skin.
The Injection Process
- Remove the Cap: Pull the clear needle cap straight off. Do not put the cap back on or touch the needle area.
- Position the Autoinjector: Place the green base of the autoinjector flat and firmly against your prepared injection site at a 90-degree angle.
- Start the Injection: Push down firmly on the device against your skin until you hear the first click. This indicates the injection has started.
- Complete the Injection: Continue holding the device firmly against your skin. The injection may take up to 15 seconds to complete. You will hear a second click and the yellow indicator in the window will fill the window completely, confirming that the dose is finished.
- Remove the Device: Once the second click has sounded and the window is yellow, lift the autoinjector straight up and away from your skin.
Post-Injection Care and Disposal
Proper aftercare and disposal are crucial for preventing infection and ensuring safety.
Aftercare
- Apply Pressure: Place a cotton ball or gauze on the injection site and press gently for several seconds. Do not rub the area, as this can increase bruising.
- Apply a Bandage: A small bandage can be applied if needed.
- Check for Reactions: Monitor the site for redness, swelling, or pain. While mild injection site reactions are common, contact your doctor if they worsen or do not resolve within a few days.
Proper Disposal
- Immediate Disposal: Immediately place the used Hadlima PushTouch autoinjector into your designated sharps disposal container.
- Do Not Reuse: Never reuse an autoinjector.
- Seal the Container: Once the sharps container is about three-quarters full, seal it securely with its lid and tape.
- Follow Local Guidelines: Contact your local waste management services, healthcare provider, or pharmacy for information on proper sharps container disposal procedures in your area.
Hadlima PushTouch vs. Standard Prefilled Syringe
The Hadlima PushTouch autoinjector and a standard prefilled syringe offer different injection experiences. Below is a comparison to help you understand the key differences.
| Feature | Hadlima PushTouch Autoinjector | Standard Prefilled Syringe |
|---|---|---|
| Activation | Buttonless, activated by pressing firmly against the skin. | Requires the user to press a plunger to inject the medication. |
| Injection Process | Automated and consistent, indicated by two distinct clicks and a yellow window indicator. | Manual, relying on the user to slowly and steadily push the plunger. |
| Needle Visibility | Conceals the needle within the green base, reducing potential needle anxiety. | Needle is exposed, which may cause some anxiety for users. |
| Needle Guard | Features an automatic needle guard that covers the needle upon removal. | Many designs require manual activation of a safety sheath or have no guard. |
| Grip and Shape | Square shape and non-slip grip provide a stable hold. | Requires a steady grip, holding it like a pen or dart. |
Conclusion
Understanding how to inject Hadlima Push Touch injection is a critical part of managing your treatment. The design of the PushTouch autoinjector aims to simplify the process, with its buttonless activation and clear confirmation clicks. By following the preparation, injection, and disposal steps carefully, you can administer your medication safely and confidently. Always consult your healthcare provider if you have any questions or concerns about your injection technique or medication.
Key Takeaways
- Prepare your injection: Gather all supplies, wash your hands, and let the Hadlima PushTouch autoinjector reach room temperature for 15-30 minutes before use.
- Inspect the medication: Check the autoinjector for damage and ensure the liquid is clear and colorless to pale brown before use.
- Select injection site: Choose a new spot on your abdomen or thigh for each injection, avoiding tender, bruised, or hard areas.
- Engage the autoinjector: Press the green base firmly against your skin until you hear two clicks. The first starts the injection, and the second signals it is complete.
- Dispose safely: Place the used autoinjector in a designated sharps container immediately after injection. Never reuse the device.
